How to remove adhesive from shower walls? I’ve got you covered if you are looking for the fastest, most effective, and least damaging way to remove glue from your bathroom walls and floors.
Not only that, but I’ve got seven different methods to remove sticky / silicone adhesive from shower walls in this infographic, so you can choose which will work best based on your situation! Check out my seven-step guide below!
Read More: How to Glue Shower Walls?
How to Remove Adhesive from Shower Wall?
Method 1: Squeegee Method
The squeegee method is one of the most popular ways to remove adhesive from shower walls. All you need is a rubber squeegee and some elbow grease.
First, wet the adhesive with warm water. Then, use the squeegee to scrape away the adhesive. Start at the top of the wall and work your way down. If the adhesive is stubborn, you may need to use a little soap or detergent to help loosen it up.
Once you’ve removed all the adhesive, rinse the area with warm water and dry it off with a towel. If any adhesive remains, repeat the process until it’s gone.
Read More: Best Adhesive for Shower Walls
Method 2: Press On, Peel Off Method
- Apply pressure to the adhesive with your fingertips, a putty knife, or a similar object.
- Start at one corner and slowly peel the adhesive off in one strip.
- If the adhesive is proving difficult to remove, you can use a hair dryer or heat gun on a low setting to heat the adhesive and make it easier to remove.
- For tougher adhesives, you may need to use a solvent such as acetone, alcohol, or mineral spirits. Test the solvent on a small area first to ensure it won’t damage your shower wall surface.
- Saturate a rag with your chosen solvent and apply it liberally to the adhesive.
- Allow the solvent to soak into the adhesive for about 10 minutes, then scrape away any remaining residue with a paint scraper.
- Repeat steps 5-6 if necessary until all of the adhesives have been removed from your shower wall.
This method can help you to remove 3M adhesive from wall.
Method 3: Scrape and Sand Method
One of the quickest ways to remove adhesive is to scrape and sand it off. You’ll need a putty knife or a razor blade and some sandpaper.
First, use the putty knife or razor blade to scrape off as much of the adhesive as possible. Then, use the sandpaper to rough up the area where the adhesive was.
This will help the new adhesive adhere better. Once you have removed as much of the old adhesive as possible, apply new adhesive using your hand or with a trowel.
Method 4: Use a Degreaser
A degreaser is an answer if you have a greasy or oily substance on your shower wall. You can buy a commercial degreaser or make your own with dish soap and water.
Apply the degreaser to the adhesive and let it sit for a few minutes. Then, use a scrub brush to remove the adhesive. If the adhesive is still there, you can try using vinegar or nail polish remover. Vinegar should be applied first to soften the adhesive.
After that, apply some acetone (nail polish remover) to loosen up any remaining residue. A final note is that if the chemicals are left too long on the wall’s surface, they will eventually cause damage to it.
It’s important to read all labels before applying these products and ensure you’re not allergic!
Read More: How to Remove Adhesive Hooks from Wall?
Method 5: Try Abrasive Polishing Pads
One way is to try abrasive polishing pads. This method will work best if the adhesive is on a hard surface. You must wet the area and then rub the pad over the adhesive. You may need to do this several times to get all of the adhesive off.
Wetting the area first means you are less likely to cause any damage or scratches on your surface.
One issue with this method is that it can take a lot of time. You may consider renting a floor sander machine from your local hardware store for large areas.
Method 6: Heat It And Soak The Wall
Start by heating the adhesive with a hair dryer or heat gun. This will help to loosen it and make it easier to remove.
If the adhesive is still stubborn, you can try soaking it in hot water for a few minutes.
Another option is to use a putty knife or razor blade to scrape off the adhesive. Just be careful not to damage the surface of your shower wall.
Method 7: Spraying On Chemicals
Spraying on chemicals is one of the most common ways to remove adhesive from shower walls. You can buy a commercial adhesive remover or make your own with white vinegar and water.
Spray the solution on the adhesive and let it sit for a few minutes. Then, use a putty knife or scraper to remove the softened adhesive.
Don’t worry about taking off any paint; that’s what you’re trying to do! Continue applying the solvent and scraping until all the adhesives have been removed.
Read More: How To Remove Self-Adhesive Shower Door Handles?
Last Opinion
You can remove adhesive from your shower wall in a few ways. You can use a product like Goo Gone, specifically designed to remove adhesives. You can also try using WD-40 or vinegar.
If you have a little time and patience, you can also try using a putty knife or razor blade. Make sure you are careful and take your time whichever method you choose.
